WEF-QG-1001 cylinder magnetic switch thermal control position control, pneumatic butterfly valve, pneumatic ball valve WEF-QG-1001 cylinder magnetic switch thermal control position control is to set one or more magnetic spring switches in a closed metal or plastic pipe, and then pass the pipe through one or more hollow floating balls with ring shaped magnets inside, and use a fixed ring to control the floating ball and magnetic spring switch in relevant positions, so that the floating ball can float up and down within a certain range. Use the magnet inside the floating ball to attract the contact point of the magnetic spring switch, generating opening and closing actions. 1、 Requirements for designers and users of pneumatic systems: 1. Confirmation of product model and specifications before use& nbsp;  Designers of pneumatic systems and designers of pneumatic components should determine the specifications of pneumatic components based on the performance requirements for the pneumatic system, taking into account performance and potential failures, and based on new product samples and data. If necessary, corresponding analysis and experiments should be conducted. When used in certain emerging industries or industries, it is necessary to collaborate with manufacturers to carry out styling design work in order to *. 2. Special attention should be paid to the following situations: 1) If compressed air is used incorrectly, it can be dangerous. Therefore, the assembly, operation, and maintenance of pneumatic equipment should be carried out by trained and experienced personnel; 2) Before confirmation, it is not allowed to use pneumatic equipment or disassemble pneumatic components from the equipment; 3) After confirming that the above treatment has been carried out, cut off the power and air supply, and discharge the remaining compressed air in the pneumatic system before maintenance and disassembly can be carried out; 4) Before starting the pneumatic equipment, it is necessary to confirm that there will be no rapid extension of the plug rod. 2、 The requirements for the use environment of pneumatic systems: 1. When used in environments with corrosive agents, chemicals (such as organic solvents), seawater, water, and non steam, or in places where the above substances are attached, they can be used conditionally. Seals, valve bodies, etc. that come into contact with the medium need to be changed to materials; 2. Avoid using in sexual settings (if necessary, consider taking measures); 3. Do not use in situations with vibration and impact, or the vibration and impact resistance of various pneumatic components should comply with the regulations on the product sample. 4. Do not use in places with heat sources or affected by radiation, or take measures to block radiation heat; 5. In places with strong direct sunlight, add protective covers. Appropriate protective measures should be taken when using in places with high humidity, high dust content, or places with water droplets, oil droplets, cutting oil, or coolant droplets. Magnetic cylinders should not be used in environments with strong magnetic fields. 6. In a temperature environment: 1) In a temperature environment: please use temperature resistant seals; 2) In a warm environment, there may be phenomena such as water freezing and poor operation in the circuit. At this time, attention should be paid to removing water to prevent freezing. 3、 The requirements for compressed air in pneumatic systems: 1. Compressed air discharged by the air compressor cannot be directly used. Compressed air contains a certain amount of water, oil, and dust. After compression, the temperature of the air reaches around 140-170 ℃, and some of the water and oil have become gaseous; 2. Introduction and specifications of the purified compressed air cylinder magnetic switch series TAIYO magnetic switch, SR101, SR201, SR401, YR201, CK-TOHCK-T2H, CK3-X1, CK3-Y1, CK-A, CK3-U, CK3-V1C magnetic switch, - A93, - A54, - C73, - A73, 2CWEF series pneumatic butterfly valves: WEF-QG-1001 represents a single node, outputting one open or close position contact< WEF-QG-2002 represents a dual node, conversion type, with open and close contact conversion output< WEF-QG-2001 represents dual node, synchronous, with synchronous output for open and close contacts. Application scope of WEF series pneumatic butterfly valve:
Furnace control: inlet and outlet of coal mill separator, hot and cold air speed cut-off valve, pebble coal, soot blower, oil control valve, coal mill oil station oil level gauge, turning gear, etc< This product can be used well in any part where mechanical travel switches can be used. WEF-QG-1001 position control switch is sold at factory price with a one-year warranty,. If you need to order, please choose Zhuoxin brand.