The principle of the DLS-I waterproof bidirectional rope switch is that the rope switch consists of a pull rod, a reset handle, a cam, a locking groove, and a micro switch. The pull rope switch is installed on the frames on both sides of the belt conveyor, and is connected along both sides of the conveyor with a steel wire rope. When an emergency occurs in the conveyor belt equipment, the steel wire rope is pulled at any location along the site, and the steel wire rope drives the drive arm to rotate. The precision cam is displaced by the torque spring driven by the transmission shaft, and the micro switch is driven to cut off the control line, causing the conveyor to stop running. The installation and adjustment of the DLS-I waterproof bidirectional pull rope switch should be installed in a place with maintenance channels on both sides of the conveyor, and the installation position should ensure that maintenance personnel can operate conveniently in emergency situations. 1. Fix the rope switch on the rack. 2. The distance between the two switches on one side is about 50m, using a diameter ofΦ The steel wire rope connection of 4 should have moderate elasticity. 3. To reduce the impact of the weight of the steel wire rope on the start of the switch, a support ring is installed on the frame every 3 meters to support the steel wire rope. 4. The other end of the steel wire rope is tied to the tension spring (fixed with a rope buckle), and the tension on both sides of the rope is tightened using a tightener without affecting normal useAnd ensure that the tension on both sides is balanced. (Note: For the climbing section conveyor, the switch spacing and rope length should be minimized as much as possible.) DLS-I waterproof bidirectional rope switch precautions: 1. Cut off the main power supply first, and then use a multimeter to measure the live wire. The switch must be installed at one end of the live wire. 2. Cut the live wire in a suitable place, and there are two joints, and the pull switch also has two joints. 3. Peel off the two joints of the live wire and expose the metal wire, and connect them to either of the two joints of the switch. 4. Cut off the excessively long metal wire at the connected joint to prevent two metal wires from colliding and short circuiting. 5. Loosen the cover of the pull switch and you can see a metal shaft with a hole at one end. 6. There is also a hole on the side of the plastic casing of the pull switch. First, pass the pull wire through the opening of the plastic casing to introduce the pull wire into the pull switch. Then, insert one end of the introduced pull wire into the shaft and tie a knot. Shorten the excessively long pull wire after tying. 7. Rotate the cover of the cable switch to prevent electric shock. DLS-I waterproof bidirectional rope switch is a switch type sensor (i.e. contactless travel switch) mainly used as a protective device for emergency parking of conventional belt conveyors, shuttle conveyors, skirt type feeding conveyors, bucket elevators, packaging production lines, stacking/reclaiming systems, cranes, excavators, ship loading and unloading systems, horizontal feeders, and other equipment on site. When an emergency occurs, pulling the rope switch at any location along the site can issue a shutdown signal, achieving protection for personnel and equipment. Because it has the characteristics of both a travel switch and a micro switch, as well as sensing performance, and is reliable in action, stable in performance, fast in frequency response, long in service life, strong in resistance to interference, waterproof, shockproof, and corrosion-resistant. Widely used in industries such as machinery, mining, textiles, printing, chemical engineering, metallurgy, light industry, valves, power, security, railways, transportation, cement, ports, etc. Pull cord switches may be used in some enterprises, but they may not be seen in many places. In fact, some rural areas still use pull cord switches. Although the people have become wealthy, some rural areas still use drawstring switches< E3S-GS7N E3S-GS7N2 E3S-GS7P E3S-GS7P2 E3S-GS10N E3S-GS10N2 E3S-GS10P E3S-GS10P2 E3S-GS30E4 E3S-GS30E2 E3S-GS30E42 E3S-GS30F4 E3S-GS30F2 KS-C2 BZJ-211 BZJ-311 photoelectric relay, electronic speed switch YT523B& GD-CH050 YT671A reflector TD-02& TD-03 Analog, Hall type proximity switch J4-D8V JCW-30QA; JCW-40QA JCW-48QA  NJK-5001C NJK-5001D  NJK-5001ANJK-5001B NJK-5002C NJK-5002D NJK-5002CD NJK-5002A NJK-5002B NJK-5002ABNJK-8002C NJK-8002D NJK-8002CD NJK-8002A NJK-8002B NJK-8002AB NJK-5003C NJK-5003D NJK-5003CD NJK-5003A NJK-5003B NJK-5003AB
Cylindrical photoelectric switch E3F01-2DN1-2L E3F01-2DN2-2L E3F01-2DP1-2L E3F01-2DP1-2L E3F01-2DP2-2L E3F1-DS8C4  E3F1-DS8B2    E3F1-DS8P1 E3F1-DS8P2  E3F1-R1NK E3F1-R1N2 E3F1-R1PK E3F1-R1P2 E3F1-3DN1-3L E3F1-3DN2-3L E3F1-3DP1-3L E3F1-3DP2-3L E3F-DS10C4E3F-DS10B2   E3F-DS10C3   E3F-DS10P1   E3F-DS10P2   E3F-DS10P3   E3F-DS10XE3F-DS10Y1 E3F-DS10Y2   E3F-DS30C4 E3F-DS30B2 E3F-DS30C3   E3F-DS30P1   E3F-DS30P2   E3F-DS30P3    E3F-DS30X   E3F-DS30Y1 E3F-DS30Y2   E3F- R2NKE3F- R2N2 E3F- R2N3  E3F- R2PK  E3F- R2P2 E3F- R2P3   E3F- R2X   E3F- R2Y1E3F- R2Y2 E3F-5DN1-5L E3F-5DN2-5L E3F-5DN3-5L E3F-5DP1-5L E3F-5DP2-5LE3F-5DP3-5L E3F-5DX-5L E3F-5DY1-5LY E3F-5DY2-5LY   E3F3-D11   E3F3-D61E3F3-D31 E3F3-D81 E3F3-D12 E3F3-D62 E3F3-D32 E3F3-D82 E3F3-R11 E3F3-R 61   E3F3-R31    E3F3-R81    E3F3-T11   E3F3-T61   E3F3-T31    E3F3-T81E3F3- DS70N1 E3F3- DS70N2 E3F3- DS70N3   E3F3- DS70P1   E3F3- DS70P1   E3F3- DS70P3   E3F3- DS70Y1   E3F3- DS70Y2  E3F3- R4NK   E3F3- R4N2      E3F3- R4N3   E3F3- R4PK   E3F3- R4P2   E3F3- R4P3    E3F3- R4Y1   E3F3- R4Y2E3F3- 10DN1-10L   E3F3- 10DN2-10L   E3F3- 10DN3-10L   E3F3- 10DP1-10L     E3F3- 10DP2-10L      E3F3- 10DP3-10L      E3F- 10DY1-10LY      E3F- 10DY2-10LYCDD-11N（40N）   & nbsp;  CDD-11P（40P）